Hello, welcome to Jiangyin Fuding Communication Equipment Co.,LTD.

FDK-380BXAP

FDK-380BXAP
NAME: FDK-380BXAP
TYPE: Piezo Transducer&Buzzer
DRIVE: Active buzzer
PROCESS: Pin buzzer
SIZE: >30mm
Description

A. SCOPE
This specification applies Piezo buzzer, FDK-380BXAP220VAC

B. SPECIFICATION

No.

Item

Unit

Specification

Condition

1

Oscillation Frequency

KHz

2.9±0.5

 

2

Operating Voltage

VAC

150 ~260

 

3

Rated Voltage

VAC

220

 

4

Current Consumption

mA

MAX. 10

at Rated Voltage

5

Sound Pressure Level

dB

MIN. 85

at 100cm at Rated Voltage

6

Tone

 

Fast Pulse

 

7

Operating Temperature

-20 ~ +60

 

8

Storage Temperature

-30 ~ +70

 

9

Dimension

mm

Φ43.0 x H46.5

See appearance drawing

10

Weight (MAX)

gram

60

 

11

Housing Material

 

ABS( Black )

 

12

Leading Pin

 

 Plating (Ni)

See appearance drawing

13

Environmental 
Protection Regulation

 

 RoHS

 

 
C. APPEARANCE DRAWING 

Tol : ± 0.5      Unit: mm


D.TESTING METHOD   
Standard Measurement conditions
Temperature:25±2℃  Humidity:45-65%

Acoustic Characteristics:
The oscillation frequency, current consumption and sound pressure are measured by the measuring instruments shown below

In the measuring test, buzzer is placed as follows:

 
E. VOLTAGE / CURRENT / SOUND PRESSURE CHARACTERISTICS

 

F. RELIABILITY TEST

NO.

ITEM

TEST CONDITION AND REQUIREMENT

1

High Temperature
Test (Storage)

After being placed in a chamber with 702℃ for 96 hours and then being placed in normal condition for 2 hours.
Allowable variation of SPL after test: 10dB.

2

Low Temperature
Test (Storage)

After being Placed in a chamber with -302℃ for 96 hours and then being placed in normal condition for 2 hours.
Allowable variation of SPL after test: 10dB.

3

Humidity Test

After being Placed in a chamber with 90-95% R.H. at 402℃ for 96 hours and then being placed in normal condition for 2 hours.
Allowable variation of SPL after test: 10dB.

4

Temperature Cycle
Test

The part shall be subjected to 5 cycles. One cycle shall be consist of:
 
Allowable variation of SPL after test: 10dB.

5

Drop Test

Drop on a hard wood board of 4cm thick, any directions ,6 times, at the height of 75cm .
Allowable variation of SPL after test: 10dB.

6

Vibration Test

After being applied vibration of amplitude of 1.5mmwith 10 to 55 Hz band of vibration frequency to each of 3 perpendicular directions for 2 hours .
Allowable variation of SPL after test: 10dB.

7

Solderability
Test

Lead terminals are immersed in rosin for 5 seconds and then immersed in solder bath of +3005℃ for 31 seconds .
90% min. lead terminals shall be wet with solder
(Except the edge of terminals).

8

Terminal Strength
Pulling Test

The force of 9.8N(1.0kg) is applied to each terminal in axial direction for 10 seconds.
No visible damage and cutting off.

TEST CONDITION.
Standard Test Condition        :      a) Temperature : +5 ~ +35℃  b) Humidity : 45-85%        c) Pressure : 860-1060mbar
Judgment Test Condition       :      a) Temperature : +25 ± 2℃    b) Humidity : 60-70%        c) Pressure : 860-1060mbar
 

G. PACKING STANDARD

CLOSE
TOP